1 User's Guide Notations Used in This Guide f Safety Indications So that you can use the projector safely and correctly, symbols are applied in the documentation and on the projector to indicate possible harm to the user or to others and the risk of damage to property. The indications and their meaning are as follows. Make sure you understand them properly before reading the guide. 2 Warning Caution Indicates the possibility of death or serious injury if this symbol is ignored or if sufficient care is not taken. Indicates the possibility of injury or damage to property if this symbol is ignored or if sufficient care is not taken. f General Information Indications Attention Indicates procedures which may result in damage or injury if sufficient care is not taken. Indicates additional information and points which may be useful to know regarding a topic. Indicates a page where detailed information regarding a topic can be found. Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary" section of the "Appendices". s p.65 Indicates operating methods and the order of operations. The procedure indicated should be carried out in the order of the numbered steps. Indicates the name of the buttons on the remote control or the control panel. Example: [Esc] button Indicates configuration menu items. Example: "Image" - "Brightness" Indicates that the explanation continues on the following page. Clicking this symbol will display the following page. Indicates that the explanation is continued from the previous page. Clicking this symbol will display the previous page. q s g Procedure [ (Name) ] "(Menu Name)" Contents Projector Features......................................................................................4 Part Names and Functions ........................................................................5 Front/Top.............................................................................................................. 5 Rear (EMP-83/822 Only)...................................................................................... 6 Rear (EMP-X5/S5 Only)....................................................................................... 7 Control Panel ....................................................................................................... 8 Remote Control .................................................................................................. 10 Base ................................................................................................................... 11 3 Appendices Installation Methods ................................................................................ 49 Cleaning .................................................................................................... 50 Cleaning the Projector's Surface ....................................................................... 50 Cleaning the Lens.............................................................................................. 50 Cleaning the Air Filter and Air Intake Vent......................................................... 50 Replacing Consumables ......................................................................... 51 Replacing the Remote Control Batteries ........................................................... 51 Replacing the Lamp........................................................................................... 52 Replacing the Air Filter ...................................................................................... 56 Useful Functions Changing the Projected Image (Source Search) ...................................13 Functions for Enhancing Projection.......................................................14 Selecting the Projection Quality (Selecting Color Mode) ................................... 14 Hiding the Image and Sound Temporarily (A/V Mute) ....................................... 15 Freezing the Image (Freeze).............................................................................. 16 Changing the Aspect Ratio (Aspect) .................................................................. 16 Enlarging Part of the Image (E-Zoom) ............................................................... 17 Saving a User's Logo............................................................................... 57 Screen Size and Distance........................................................................ 59 EMP-83/822/X5 ................................................................................................. 59 EMP-S5 ............................................................................................................. 60 Connecting to External Equipment ........................................................ 61 Connecting to an External Monitor .................................................................... 61 Connecting to External Speakers (EMP-83/822 Only) ...................................... 61 Security Functions ...................................................................................18 Managing Users (Password Protect) ................................................................. 18 Restricting Operation (Operation Lock).............................................................. 20 Anti-Theft Lock ................................................................................................... 21 Configuration Menu Using the Configuration Menu ................................................................23 List of Functions.......................................................................................24 Image Menu (EMP-83/822 Only) ....................................................................... 24 Image Menu (EMP-X5/S5 Only)......................................................................... 25 Signal Menu (EMP-83/822 Only) ....................................................................... 26 Signal Menu (EMP-X5/S5 Only)......................................................................... 27 Settings Menu .................................................................................................... 28 Extended Menu .................................................................................................. 29 Network Menu (EMP-83/822 Only) .................................................................... 31 Info Menu (Display Only).................................................................................... 34 Reset Menu........................................................................................................ 35 Connecting a LAN Cable (EMP-83/822 Only)......................................... 62 Connecting a USB Cable (EMP-X5/S5 Only).......................................... 63 Optional Accessories and Consumables .............................................. 64 Glossary.................................................................................................... 65 ESC/VP21 Commands ............................................................................. 67 Command List.................................................................................................... 67 Cable Layouts.................................................................................................... 67 Connecting a USB (EMP-X5/S5 Only)............................................................... 68 USB Connection Setup...................................................................................... 68 PJLink (EMP-83/822 Only) ....................................................................... 69 List of Supported Monitor Displays ....................................................... 70 Specifications........................................................................................... 71 Appearance............................................................................................... 75 Index.......................................................................................................... 76 Troubleshooting Using the Help ..........................................................................................37 Problem Solving .......................................................................................38 Reading the Indicators ....................................................................................... 38 When the Indicators Provide No Help ................................................................ 41 Projector Features Ease of use Enhanced security functions 4 f The A/V mute slide makes it easy to project and store You can stop and resume projection easily by opening and closing the A/V mute slide which makes giving clear presentations easier. f Password Protect to restrict and manage users By setting a password you can restrict who can use the projector. s p.18 f Operation Lock restricts button operation on the control panel You can use this to prevent people from changing projector settings without permission at events, in schools, and so on. s p.20 f A single foot design means you do not have to make any difficult levelling adjustments You can easily make height adjustments with one hand. sQuick Start Guide f Equipped with various anti-theft devices The projector is equipped with the following security devices. s p.21 • Security slot • Security cable installation point Easy to handle f Direct power On/Off (EMP-83/822 only) In places where power is managed centrally, such as in a conference room, the projector can be set to power on and off automatically when the power source to which the projector is connected is switched on or off. f No cool down delay After turning the projector's power off, you can disconnect the projector's power cable without having to wait for the projector to cool down first. Part Names and Functions Front/Top K A B C J I H D E F Name Function 5 Front adjustable feet Foot adjust lever A/V mute slide Extend and adjust the position of the projected image when the projector is placed on a surface such as a desk. s Quick Start Guide Pull out the foot lever to extend and retract the front foot. s Quick Start Guide Slide shut when not using the projector to protect the lens. By closing during projection you can hide the image and the sound (A/V Mute). s Quick Start Guide, p.15 Receives signals from the remote control. s Quick Start Guide Adjusts the image focus. s Quick Start Guide Adjusts the image size. s Quick Start Guide G G F E D Name Function Remote receiver Focus ring Zoom ring (EMP-83/822/X5 only) A/V mute slide knob Security slot (j) H I J K Slide the knob to open and close the A/V mute slide. The security slot is compatible with the Microsaver Security System manufactured by Kensington. s p.21 A B C Control panel Lamp cover Air exhaust vent s p.8 Open this cover when replacing the projector's lamp. s p.53 Caution Do not place objects that may become warped or otherwise affected by heat near the air exhaust vent and do not put your face or hands near the air exhaust vent while projection is in progress. Part Names and Functions 6 Rear (EMP-83/822 Only) A H G F E Name Function RS-232C port When controlling the projector from a computer, connect it to the computer with an RS-232C cable. This port is for control use and should not normally be used. s p.67 For video signals from a computer and component videog signals from other video sources. F Computer1 input port Audio1 input port Connect to the audio out port of the computer connected to the Computer1 input port. Computer2 input port For video signals from a computer and component videog signals from other video sources. B Name C D E Function A B C Remote receiver Speaker Monitor Out port Receives signals from the remote control. s Quick Start Guide Audio2 input port Connect to the audio out port of the computer connected to the Computer2 input port. s Quick Start Guide G S-Video input port Video input port Audio-L/R input port For S-videog signals from video sources. For composite videog signals from video sources. Connects to the audio out port of the equipment connected to the S-Video port or Video input port. s Quick Start Guide When a LAN cable is connected, you can monitor and control the projector over a LAN. s p.62 Outputs the image signal from the computer connected to the Computer1 input port to an external monitor. This is not available for component videog signals or other signals being input to any port other than the Computer1 input port.s p.61 Outputs the sound of the image currently being projected to external speakers. s p.61 Connects to the power cable. s Quick Start Guide H LAN port Audio Out port D Power inlet Part Names and Functions 7 Rear (EMP-X5/S5 Only) A I HG F E D E F G H B Name Name Function Computer input port Audio-L/R input port Video input port S-Video input port For video signals from a computer and component videog signals from other video sources. Connects to the audio output port for the equipment you want to project from and inputs the audio. s Quick Start Guide For composite videog signals from video sources. For S-videog signals from video sources. C Function I A B C D Remote receiver Speaker Power inlet Monitor Out port Receives signals from the remote control. s Quick Start Guide Connects to the power cable. s Quick Start Guide Outputs the image signal from the computer connected to the Computer input port to an external monitor. This is not available for component videog signals or other signals being input to any port other than the Computer input port.s p.61 USB port (Type B) When showing a slide show in PowerPoint, you can use the projector's remote control to move to the next slide/previous slide if it is connected to a computer by a USB cable.* Also, you can use it as a control port when the projector is controlled by a computer. Even if the projector is connected to a computer by a USB cable, you cannot project the image on the computer. s p.63 * Limited to computers with the following operating systems installed. Windows 98/98SE/2000/Me/XP Home Edition/XP Professional Macintosh: OS 8.6 to 9.2/10.1 to 10.3 Part Names and Functions 8 Control Panel f EMP-83/822/X5 Name Function A I H G B C D [Power] button Status indicators Turns the projector power on or off. s Quick Start Guide The color of the indicators and whether they are flashing or lit indicates the status of the projector. s p.38 Changes to the next input source that is connected to the projector and is sending an image.s p.13 If pressed during projection of computer signal images, it automatically adjusts the tracking, synchronization, and position to project the optimum image. When a configuration menu or a help screen is displayed, it accepts and enters the current selection and moves to the next level.s p.23 Corrects keystone distortion. If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values. s Quick Start Guide, p.23 Displays and closes the help screen which shows you how to deal with problems if they occur.s p.37 Stops the current function. If pressed when a configuration menu is displayed, it moves to the previous menu level.s p.23 Press to adjust the volume. If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values. s Quick Start Guide, p.23 A [Source Search] button [Enter] button B f EMP-S5 C D E F E [v] [w] buttons Buttons without numbers operate in the same way as in the figure above. See the numbers in the table for the figure above. J F G [Help] button [Esc] button H [a] [b] buttons (EMP-83/822/X5 only) Part Names and Functions 9 Name Function I J [Menu] button [Wide] [Tele] buttons (EMP-S5 only) Displays and closes the configuration menu.s p.23 Adjusts the image size. If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values. s Quick Start Guide, p.23 Part Names and Functions 10 Name Function Remote Control P O N M L K J I H G C D A B C D E F G [Menu] button [Enter/Auto] button Displays and closes the configuration menu. s p.23 If pressed during projection of computer signal images, it automatically adjusts the tracking, synchronization, and position to project the optimum image. s p.26 When a configuration menu or a help screen is displayed, it accepts and enters the current selection and moves to the next level.s p.23 Each time the button is pressed, the color mode changes.s p.14 When showing a slide show in PowerPoint, you can use the projector's remote control to move to the next slide/previous slide if it is connected to a computer by a USB cable.* s p.63 (+) Enlarges the image without changing the projection size. (-) Reduces parts of the image that have been enlarged using the [+] button.s p.17 E F [Color Mode] button [Page] button (Down) (Up) (EMP-X5/S5 only) [E-Zoom] button (+) (-) H Illustrations show EMP-X5/S5. Name Function [A/V Mute] button Turns the video and audio on or off. s p.15 [Freeze] button [Aspect] button Numeric buttons Images are paused or unpaused.s p.16 The aspect ratiog changes each time the button is pressed.s p.16 Use these buttons when entering a password. s p.19 I J K A B [Power] button [Source Search] button Turns the projector power on or off. s Quick Start Guide Changes to the next input source that is connected to the projector and is sending an image.s p.13 * Limited to computers with the following operating systems installed. Windows 98/98SE/2000/Me/XP Home Edition/XP Professional Macintosh: OS 8.6 to 9.2/10.1 to 10.3 Part Names and Functions 11 Name Function Base D L [Volume -] button Press [Volume -] to lower the volume and [Volume +] button press [Volume +] to raise the volume. If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values. s Quick Start Guide , p.23 [Esc] button Stops the current function. If pressed when a configuration menu is displayed, it moves to the previous level. s p.23 Displays and closes the help screen which shows you how to deal with problems if they occur.s p.37 If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values. s p.23 Outputs remote control signals. s Quick Start Guide M N O P A [Help] button [u] [d] buttons B C Name Function Remote control light-emitting area B Suspension bracket fixing points (3 points) Rear foot (2 points) Security cable installation point Air filter (Air intake vent) Attach the optional ceiling mount here when suspending the projector from a ceiling. s p.49, 64 Turn to extend and retract to adjust the horizontal tilt. s Quick Start Guide Pass a commercially available anti-theft wire lock through here when you want to secure the projector to a fixed object. s p.21 This prevents dust and other foreign particles from getting inside the projector when air is drawn in. The projector displays a warning message when it is time to clean or replace the air filter.s p.50, 56 A B C D Useful Functions This chapter explains useful functions for giving presentations and so on, and the security functions. Changing the Projected Image (Source Search) .................................................. 13 Functions for Enhancing Projection ................. 14 • Selecting the Projection Quality (Selecting Color Mode) .....................................................14 • Hiding the Image and Sound Temporarily (A/V Mute) .........................................................................15 • Freezing the Image (Freeze).............................................16 • Changing the Aspect Ratio (Aspect)................................16 • Enlarging Part of the Image (E-Zoom) ...........................17 Security Functions..............................................18 • Managing Users (Password Protect)............................... 18 Type of Password Protect .............................................................. 18 Setting Password Protect................................................................ 19 Entering the Password.................................................................... 20 • Restricting Operation (Operation Lock)........................ 20 • Anti-Theft Lock ................................................................ 21 Installing the wire lock................................................................... 21 Changing the Projected Image (Source Search) The projector automatically detects signals being input from connected equipment, and the image being input from the equipment is projected. You can project the target image quickly because it skips input ports where no image is being input. Computer1 Computer2* S-Video Video 13 q The following screen showing the status of image signals is displayed when only the image that the projector is currently displaying is available, or when no image signal can be found. You can select the input port where the connected equipment you want to use is projecting. If no operation is performed after about 10 seconds, the screen closes. For EMP-83/822 The input port where no image signal is being input is skipped. * EMP-83/822 only Procedure When your video equipment is connected, start playback before beginning this operation. Using the remote control Using the control panel When two or more pieces of equipment are connected, press the [Source Search] button until the target image is projected. Functions for Enhancing Projection Selecting the Projection Quality (Selecting Color Mode) You can easily obtain the optimum image quality simply by selecting the setting that best corresponds to your surroundings when projecting. The brightness of the image varies depending on the mode selected. Mode Game Presentation Text Theatre Photo Application Ideal for use in a bright room. This is the brightest mode and reproduces shadow tones well. Ideal for making presentations using color materials in a bright room. Ideal for making presentations using black-andwhite materials in a bright room. Ideal for watching films in a dark room. This gives images a natural tone. (When computer images are input) Ideal for projecting still pictures, such as photos, in a bright room. This makes images vivid and brings them into contrast. (When component video, S-video, or composite video images are input) Ideal for watching TV programmes in a bright room. This makes images vivid and brings them to life. Ideal for images that conform to the sRGB color standard. Even if you are projecting onto a blackboard (greenboard), this setting gives your images a natural tint, just like when projecting onto a screen. Procedure Remote control 14 Each time you press the button, the color mode name is displayed on the screen and the color mode changes. Sports sRGBg Blackboard If you press the button while the color mode name is displayed on the screen, it changes to the next color mode. q The color mode can also be set using "Color Mode" from the "Image" menu in the configuration menu. s p.24, 25 Functions for Enhancing Projection 15 Hiding the Image and Sound Temporarily (A/V Mute) You can use this when you want to focus the audience's attention on what you are saying, or if you do not want to show details such as when you are changing between files during presentations from a computer. q • If you use this function when projecting moving images, the images and sound continue to be played back by the source, and you cannot return to the point where A/V Mute was activated. • From the remote control you can choose to display black, blue, or logo* as the A/V mute display using the "Extended" - "Display" - "A/V Mute" setting in the configuration menu. s p.29 • When the A/V mute slide is closed and A/V Mute begins, the power supply can be set to automatically turn off after about 30 minutes by setting "Extended" - "Operation" "Lens Cover Timer" in the configuration menu. s p.30 Procedure Remote control Projector * Depending on the area of purchase, the User's Logo function may not be available for EMP-X5/S5. Each time you press the button, or the A/V mute slide is opened or closed, A/V Mute turns on or off. Functions for Enhancing Projection 16 Freezing the Image (Freeze) When the moving image on the screen is frozen, the image continues to project, so you can project a moving image one frame at a time like a still photo. Also, you can perform operations such as changing between files during presentations from a computer without projecting any images if the Freeze function is activated beforehand. Procedure Remote control Changing the Aspect Ratio (Aspect) When video equipment is connected, images that have been recorded in digital video or onto DVDs can be viewed in 16:9 wide-screen format. You can change the aspect ratiog for images in squeeze modeg as follows. 4:3 16:9 16:9 (Up) 16:9 (Down) Procedure Remote control Each time you press the button, Freeze turns on or off. q • Audio does not stop. • The image source continues to play back the moving images even while the screen is frozen, so it is not possible to resume projection from the point where it was paused. • If the [Freeze] button is pressed while the configuration menu or a help screen is displayed, the menu or help screen being displayed is cleared. • Freeze still works while E-Zoom is being used. Each time you press the button, the aspect name is displayed on the screen and the aspect changes. Functions for Enhancing Projection If you press the button while the aspect name is displayed on the screen, it changes to the next aspect mode. 17 the cross to the area of the image that you B Move want to enlarge. Remote control q This can also be set using "Aspect" from the "Signal" menu in the configuration menu. s p.26 Enlarging Part of the Image (E-Zoom) This is useful when you want to expand images such as graphs and tables to see them in greater detail. Cross C Enlarge. Remote control Procedure A Start E-Zoom. Remote control Each time the button is pressed, the area is expanded. You can expand quickly by holding the button down. You can reduce the enlarged image by pressing the [-] button. Press the [Esc] button to cancel. q • The enlargement ratio appears on the screen. The selected area can be enlarged to between 1 to 4 times in 25 incremental steps. • You can scroll the image by pressing [u], [d], [l], or [r]. Security Functions The projector has the following enhanced security functions. • Password Protect You can limit who can use the projector. • Operation Lock You can prevent people from changing the settings on the projector without permission. • Anti-Theft Lock The projector is equipped with various types of anti-theft security devices. • Settings for "Display Background", "Startup Screen", and "A/V Mute" are changed from "Display" in the configuration menu. 3 "Network Protect" (EMP-83/822 only) When "Network Protect" is set to "On" setting changes for "Network" in the configuration menu are prohibited. 18 * Depending on the area of purchase, the User's Logo function may not be available for EMP-X5/S5. In that case, "User's Logo Protect" is not displayed. Managing Users (Password Protect) When the Password Protect function is activated, people who do not know the password cannot use the projector to project images even if the projector power is on. Furthermore, the user's logo that is displayed when you turn on the projector cannot be changed. This acts as an anti-theft device as the projector cannot be used even if it is stolen. At the time of purchase the Password Protect function is not activated. f Type of Password Protect The following three kinds of password protect settings can be made according to how the projector is being used. 1. "Power On Protect" When "Power On Protect" is "On", the password must be entered whenever the projector is turned on after it has been disconnected from the power supply to which it was connected the last time the password was entered. If the correct password is not entered, projection does not start. 2 "User's Logo Protect"* When "User's Logo Protect" is set to "On" the following setting changes are prohibited. • Capturing a user's logo Security Functions 19 f Setting Password Protect Use the following procedure to set Password Protect. Procedure C Turn on "User's Logo Protect" . * (1) Select "User's Logo Protect", and then press the [Enter] button. (2) Select "On", and then press the [Enter] button. (3) Press the [Esc] button. down the [Freeze] button for about five A Hold seconds. The password protect setting menu is displayed. Remote control D Turn on "Network Protect". E Set the password. (1) Select "Network Protect", and then press the [Enter] button. (2) Select "On", and then press the [Enter] button. (3) Press the [Esc] button. q • If Password Protect is already activated, you must enter the password. If the password is entered correctly, the password protect setting menu is displayed. s "Entering the Password" p.20 • When the password is set, stick the password protect sticker in a visible position on the projector as a further theft deterrent. (1) Select "Password", and then press the [Enter] button. (2) When the message "Change the password?" is displayed, select "Yes" and then press the [Enter] button. The default setting for the password is "0000". Change this to your own desired password. If you select "No", the screen shown in step 1 is displayed again. (3) Enter a four digit number using the numeric buttons. The number entered is displayed as "* * * *". When you enter the fourth digit, the confirmation screen is displayed. Remote control Numeric buttons B Turn on "Power On Protect". (1) Select "Power On Protect", and then press the [Enter] button. (2) Select "On", and then press the [Enter] button. (3) Press the [Esc] button. (4) Re-enter the password. The message "Password accepted." is displayed. If you enter the password incorrectly, a message is displayed prompting you to re-enter the password. Security Functions * Depending on the area of purchase, the User's Logo function may not be available for EMP-X5/S5. In that case, "User's Logo Protect" is not displayed. 20 Restricting Operation (Operation Lock) Do one of the following to lock the operation buttons on the control panel. • Full Lock All of the buttons on the control panel are locked. You cannot perform any operations from the control panel, including turning the power on or off. • Operation Lock All of the buttons on the control panel, except for the [Power] button, are locked. This is useful at events or shows when you want to deactivate all buttons and only project, or at schools when you want to limit button operation. The projector can still be operated using the remote control. Procedure f Entering the Password When the password entry screen is displayed, enter the password using the numeric buttons on the remote control. Procedure Enter the password by using the numeric buttons. When you enter the correct password, projection begins. Attention • If an incorrect password is entered three times in succession, the message "The projector's operation will be locked." is displayed for about five minutes, and then the projector switches to standby mode. If this happens, disconnect the power plug from the electrical outlet and then reinsert it and turn the projector's power back on. The projector displays the password entry screen again so that you can enter the correct password. • If you have forgotten the password, make a note of the "Request Code: xxxxx" number that appears on the screen and contact the nearest address provided in the International Warranty Terms. sInquiries • If you continue to repeat the above operation and input the wrong password thirty times in succession, the following message is displayed and the projector does not accept any more password entries. "The projector's operation will be locked. Contact Epson as described in your documentation." sInquiries the [Menu] button and select "Settings" A Press "Operation Lock" in the configuration menu. s "Using the Configuration Menu" p.23 Using the remote control Using the control panel Security Functions 21 Anti-Theft Lock As the projector is often setup on ceiling mounts and left in rooms unattended, it is possible that someone may try and take the projector, so the projector includes the following security devices. • Security slot The security slot is compatible with the Microsaver Security System manufactured by Kensington. You can find details about the Microsaver Security System on the Kensington homepage http://www.kensington.com/. • Security cable installation point A commercially available theft-prevention wire lock can be passed through the installation point to secure the projector to a desk or pillar. Check the buttons you can use and the operations they perform in the guide under the menu. B Select either "Full Lock" or "Operation Lock". "Yes" when the confirmation message is C Select displayed. The control panel buttons are locked according to the setting you chose. f Installing the wire lock Pass an anti-theft wire lock through the installation point. See the documentation supplied with the wire lock for locking instructions. q You can release the control panel lock by one of the following two methods. • From the remote control, select "Off" from "Settings" "Operation Lock" in the configuration menu. • When you press and hold down the [Enter] button on the control panel for about seven seconds, a message is displayed and the lock is released. Configuration Menu This chapter explains how to use the configuration menu and its functions. Using the Configuration Menu .......................... 23 List of Functions................................................. 24 • • • • • • • • • Image Menu (EMP-83/822 Only).....................................24 Image Menu (EMP-X5/S5 Only) .....................................25 Signal Menu (EMP-83/822 Only).....................................26 Signal Menu (EMP-X5/S5 Only) .....................................27 Settings Menu ....................................................................28 Extended Menu .................................................................29 Network Menu (EMP-83/822 Only) ................................31 Info Menu (Display Only).................................................34 Reset Menu ........................................................................35 Using the Configuration Menu from the A Selecting top menu Top menu 23 from the B Selecting sub menu the C Changing selected item D Exit Guide Sub menu (Settings) For EMP-83/822/X5 For EMP-S5 Buttons used Using the control panel Select the setting to change For EMP-83/ 822/X5 For EMP-S5 Using the remote control List of Functions Image Menu (EMP-83/822 Only) Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each image signal. Computer image Component videog/Composite videog/S-videog 24 Sub Menu Color Mode Brightness Contrastg Color Saturation Tint Sharpness Color Adjustment Reset Function You can select the quality of the image to suit your surroundings. s p.14 You can adjust the image brightness. You can adjust the difference between light and shade in the images. You can adjust the color saturation for the images. (Adjustment is only possible when NTSC signals are being input if you use composite video/S-video.) You can adjust the image tint. You can adjust the image sharpness. You can make adjustments by choosing one of the following Abs. Color Temp.: You can adjust the overall tint of the image. You can adjust tints in 10 stages from 5000 K to 10000 K. When a high value is selected the image becomes tinged with blue, and when a low value is selected the image becomes tinged with red. Red, Green, Blue: You can adjust the saturation of each color individually. (This item cannot be selected if "sRGBg" is selected as the "Color Mode" setting in the "Image" menu.) You can reset all adjustment values in the "Image" menu to their default settings. To return all menu items to their default settings, see s p.35 List of Functions 25 Image Menu (EMP-X5/S5 Only) Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each image signal. Computer image Component videog/Composite videog/S-videog Sub Menu Color Mode Brightness Contrastg Color Saturation Tint Sharpness Color Temp. Color Adjustment Reset Function You can select the quality of the image to suit your surroundings. s p.14 You can adjust the image brightness. You can adjust the difference between light and shade in the images. You can adjust the color saturation for the images. (Adjustment is only possible when NTSC signals are being input if you use composite video/S-video.) You can adjust the image tint. You can adjust the image sharpness. You can adjust the overall tint of the image. When "High" is selected the image becomes tinged with blue, and when "Low" is selected the image becomes tinged with red. (This item cannot be selected if "sRGBg" is selected as the "Color Mode" setting in the "Image" menu.) Red, Green, Blue: You can adjust the saturation of each color individually. (This item cannot be selected if "sRGBg" is selected as the "Color Mode" setting in the "Image" menu.) You can reset all adjustment values in the "Image" menu to their default settings. To return all menu items to their default settings, see s p.35 List of Functions 26 Signal Menu (EMP-83/822 Only) Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each image signal. Computer image Component videog Composite videog/S-videog Sub Menu Auto Setup Trackingg Sync.g Position Progressiveg Computer1 Input Computer2 Input Video Signal Aspect Reset Function You can select whether the image is automatically adjusted to the optimum state (On) or not (Off) when the input signal changes. s p.44 You can adjust computer images when vertical stripes appear in the images. s p.44 You can adjust computer images when flickering, fuzziness, or interference appear in the images. s p.44 You can adjust the display position up, down, left, and right so that all of the image is projected if a part of the image is missing. (Component video can only be adjusted when 480i/576i signals are being input) Off: IP conversion is carried out for each field in the screen. This is ideal for viewing images with a large amount of movement. On: interlaceg (i) signals are converted into progressiveg (p) signals. This is ideal for viewing still images. You can select the input signal from the Computer1 input port or Computer2 input port. If set to "Auto" the input signal is set automatically according to the connected equipment. If colors do not appear correctly when set to "Auto", select the appropriate signal according to the connected equipment. If set to "Auto", video signals are recognized automatically. If interference appears in the image or a problem occurs such as no image is being projected when set to "Auto", select the appropriate signal according to the connected equipment. You can set the aspect ratiog for projected images. s p.16 You can reset all adjustment values in the "Signal" menu to their default settings, except for "Computer1 Input" and "Computer2 Input". To return all menu items to their default settings, see s p.35 List of Functions 27 Signal Menu (EMP-X5/S5 Only) Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each image signal. Computer image Component videog Composite videog/S-videog Sub Menu Auto Setup Trackingg Sync.g Position Progressiveg Computer Input Video Signal Aspect Reset Function You can select whether the image is automatically adjusted to the optimum state (On) or not (Off) when the input signal changes. s p.44 You can adjust computer images when vertical stripes appear in the images. s p.44 You can adjust computer images when flickering, fuzziness, or interference appear in the images. s p.44 You can adjust the display position up, down, left, and right so that all of the image is projected if a part of the image is missing. (Component video can only be adjusted when 480i/576i signals are being input) Off: IP conversion is carried out for each field in the screen. This is ideal for viewing images with a large amount of movement. On: interlaceg (i) signals are converted into progressiveg (p) signals. This is ideal for viewing still images. You can select the input signal from the Computer input port. If set to "Auto" the input signal is set automatically according to the connected equipment. If colors do not appear correctly when set to "Auto", select the appropriate signal according to the connected equipment. If set to "Auto", video signals are recognized automatically. If interference appears in the image or a problem occurs such as no image is being projected when set to "Auto", select the appropriate signal according to the connected equipment. You can set the aspect ratiog for projected images. s p.16 You can reset all adjustment values in the "Signal" menu to their default settings, except for "Computer Input". To return all menu items to their default settings, see s p.35 List of Functions 28 Settings Menu For EMP-83/822 For EMP-X5 For EMP-S5 Sub Menu Keystone Auto Keystone (EMP-83/822/X5 only) Zoom (EMP-S5 only) Operation Lock Brightness Control Function You can correct vertical keystone distortion in images.s Quick Start Guide Performs automatic keystone correction. (This can only be specified when "Front" is selected from "Extended" - "Projection".) Adjusts the image size.s Quick Start Guide Wide: Larger Tele: Smaller You can use this to restrict operation of the projector's control panel. s p.20 You can set the lamp brightness to one of two settings. Select "Low" if the images being projected are too bright such as when projecting images in a dark room or onto a small screen. When "Low" is selected, the amount of electricity consumed and the lamp's operating life are changed as follows, and fan rotation noise during projection is reduced. Electrical consumption: about a 35 W decrease, lamp life: about 1.5 times longer You can adjust the volume. You can limit the reception of the operation signal from the remote control. When you want to prohibit operation by remote control, or if the remote receiver has a fluorescent light too close to it , you can make settings to deactivate the remote receiver that you do not want to use or that is experiencing interference. When the projector is setup, a test pattern is displayed so that you can adjust the projection without connecting other equipment. While the test pattern is displayed you can perform zoom adjustments, focus adjustments, and keystone correction. To cancel the test pattern, press the [Esc] button on the remote control or the control panel. You can reset all adjustment values in the "Settings" menu to their default settings. To return all menu items to their default settings, see s p.35 Volume Remote Receiver (EMP-83/822 only) Test Pattern (EMP-83/822 only) Reset List of Functions 29 Extended Menu For EMP-83/822 For EMP-X5/S5 For EMP-X5/S5 (Euro) Sub Menu Display User's Logo*1 Projection Function You can make settings related to the projector's display. Messages: You can set whether to display (On) or not display (Off) the source name when you change the input source, the color mode name when you change the Color Mode, a message when no image signal is input, and so on. Display Background*1: You can set the screen status for when no image signal is available to "Black", "Blue", or "Logo". Startup Screen*1: You can set whether the startup screen (the image projected when starting the projector) is displayed (On) or not (Off). A/V Mute*1: You can set the screen displayed during A/V Mute as "Black", "Blue", or "Logo". You can change the user's logo that is displayed as a background and displayed during A/V Mute. s p.57 You can choose one of the following settings according to the way the projector is setup. s p.49 Front" "Front/Ceiling" "Rear" "Rear/Ceiling" You can change the setting as follows by pressing down the [A/V Mute] button on the remote control for about five seconds. Front" W "Front/Ceiling" Rear" W "Rear/Ceiling" List of Functions Sub Menu Operation 30 Function Direct Power On: You can set whether Direct Power On is enabled (On) or disabled (Off). When it is set to "On" and the projector power cable is connected to an electrical outlet, be aware that sudden surges of electricity may cause the projector to turn on automatically. Sleep Mode: When set to "On", this turns off the power automatically when no image signal is input and no operations are performed. Sleep mode is set to (Off) at the time of purchase, so do not forget to turn off the power after projecting. Sleep Mode Time: When Sleep Mode is set to "On", you can set how long the projector should wait before turning off the power from 1 to 30 minutes. Lens Cover Timer: When set to "On", this turns off the power automatically 30 minutes after the lens cover is closed. Lens Cover Timer is set to (On) at the time of purchase. High Altitude Mode: Set this to "On" when using the projector above an altitude of 1500 m. Standby Mode You can use network monitoring and control functions while the projector is in standby mode when this is set to "Network On". (EMP-83/822 only) You can use SNMPg to monitor and control the status of the projector over the network, or by using the "EMP Monitor" software supplied with this product. Link 21Lg You can set whether to use the utility software EMP Link 21L (On) or not (Off). Set this to "On" and use it after installing the USB (EMP-X5/S5 only) communication driver. Language You can set the language for message displays. Reset You can reset "Display*1" and "Operation*2" in the "Extended" menu to their default settings. To return all menu items to their default settings, see s p.35 *1 When "User's Logo Protect" is set to "On" in "Password Protect", settings concerning user's logo cannot be changed. You can make changes after setting "User's Logo Protect" to "Off". s p.19 Depending on the area of purchase, the User's Logo function may not be available for EMP-X5/S5. In that case, "User's Logo" is not displayed. *2 Except for "High Altitude Mode". List of Functions 31 Network Menu (EMP-83/822 Only) When "Network Protect" is set to "On" in "Password Protect", a message is displayed and the settings cannot be changed. You can make changes after setting "Network Protect" to "Off". s p.19 Sub Menu Wired LAN Function You can make network settings. DHCP: You can set whether to use DHCP (On) or not (Off). If this is set to "On" you cannot set any more addresses. IP Address: You can input the IP address assigned to the projector.*1 You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used. 0.0.0.0, 0.x.x.x, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255) Subnet Mask: You can input the Subnet Mask for the projector.*1 You can enter a number from 0 to 255 in each field of the address. However, the following subnet masks cannot be used. 0 to 254.x.x.x. 255.255.255.255 Gateway Address: You can input the IP address for the gateway for the projector.*1 You can enter a number from 0 to 255 in each field of the address. However, the following gateway addresses cannot be used. 0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255) MAC Address: You can input the MAC Address for the projector. Enter a password to use when you access the projector using compatible PJLink software.*1 s p.69 You can enter up to 32 alphanumeric characters. Enter a password to use when making settings and controlling the projector using Web control.*1 You can enter up to 8 alphanumeric characters. Web control is a computer function that allows you to set up and control the projector by using the Web browser on a computer on which EMP Monitor is running. sEMP Monitor Operation Guide PJLink Password Web Control Password List of Functions Sub Menu SNMPg Function 32 You can make SNMP settings. Trap IP Address 1/Trap IP Address 2: You can register up to two IP addresses for the SNMP trap notification destination. The IP address registered in "Trap IP Address 2" is used when the IP address in "Trap IP Address 1" cannot be accessed. To use SNMP to monitor the projector, you need to install the SNMP manager program on your computer. SNMP should be managed by a network administrator. Mail When this is set, you are notified by e-mail if a problem or warning occurs with the projector.*2 Mail Notification: You can set whether to be notified by mail (On) or not (Off). SMTP Server: You can input the IP address for the SMTP server for the projector.*1 You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used. 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255) Port Number: You can input the port number for the SMTP server.*1 The initial value is 25. You can input numbers between 1 to 65535. Destination Address 1/Destination Address 2/Destination Address 3: You can enter*1 the destination mail address and the contents of the message to receive notification when a problem or warning occurs. You can register up to three destinations. You can enter up to 32 single-byte alphanumeric characters for the mail addresses. Projector Name You can enter a name for the projector. When connected to a network, this name is used to identify the projector. Reset You can reset all adjustment values in the "Network" menu to their default settings. To return all menu items to their default settings, see s p.35 *1 When inputting numbers and passwords, the following software keyboard is displayed. Tilt the [u], [d], [l], and [r] buttons on the remote control to move the cursor to the target key, and press the [Enter] button to input. After entering characters, press [Finish] on the keyboard to confirm your entry. Press [Cancel] on the keyboard to cancel your input. Each time this key is selected, it sets and changes between upper case and lower case letters. Each time this key is selected, it sets and changes the symbol keys for the section enclosed by the frame. List of Functions 33 *2 When the Mail Notification function is set to "On" and a problem or warning occurs with a projector, the following mail is sent. Subject: EPSON Projector First line: The name of the projector where the problem has occured Second line: The IP address set for the projector where the problem has occured Third line and on: Details of the problem The details of the problem are listed line by line. The following table explains the details shown in the message. For details on dealing with problems, see "Reading the Indicators".s p.38 Message Internal error Fan related error Sensor error Lamp cover is open. Lamp timer failure Lamp out Internal temperature error High-speed cooling in progress Lamp replacement notification Cause Internal Error Fan Error Sensor Error Lamp Cover Open Lamp Failure Lamp Error High Temp Error (Overheating) High Temp Warning Replace Lamp No signal No image signal is being input to the No-signal projector. Check the connection status and the power supply to connected equipment. A (+) or (-) will appear at the start of the message. (+): A projector problem has occured (-): A projector problem has been dealt with List of Functions 34 Info Menu (Display Only) Lets you check the status of the image signals being projected and the status of the projector. Items displayed vary depending on the image signal currently being projected as shown in the following screen shots. Computer image/Component videog Composite videog/S-videog Sub Menu Lamp Hours Function time*. You can display the cumulative lamp operating When it reaches the lamp warning time, the characters are displayed in yellow. Source You can display the input port name for the connected equipment currently being projected. Input Signal You can display the content of "Computer1" or "Computer2" set in the "Signal" menu according to the "Source". Resolution You can display the input resolution. Video Signal You can display the content of "Video Signal" set in the "Signal" menu. Refresh Rateg You can display the refresh rate. Syncg Info You can display the image signal information. This information may be needed if service is required. Status This is information about problems that have occurred on the projector. This information may be needed if service is required. * The cumulative use time is displayed as "0H" for the first 10 hours. After 10 hours or more, one hour is added for each subsequent hour. List of Functions 35 Reset Menu For EMP-83/822 For EMP-X5/S5 Sub Menu Reset All (EMP-83/822 only) Reset All (EMP-X5/S5 only) Reset Lamp Hours Function You can reset all items in all menus to their default settings. The following items are not reset to their defaults: "Computer1 Input", "Computer2 Input", "User's Logo", all items in "Network" menu, "Lamp Hours", and "Language". You can reset all items in all menus to their default settings. The following items are not reset to their defaults: "Computer Input", "Zoom" (EMP-S5 only), "User's Logo*", "Lamp Hours", and "Language". You can clear the cumulative Lamp Hours use time, and return it to "0H". Reset it when you replace the lamp. * Depending on the area of purchase, the User's Logo function may not be available for EMP-X5/S5. In that case, "User's Logo" is not displayed. Troubleshooting This chapter describes how to identify problems and what to do if a problem is found. Using the Help..................................................... 37 Problem Solving ................................................. 38 • Reading the Indicators......................................................38 t Power indicator lights red ..........................................................39 i o Indicator is lit or flashing orange...........................................40 • When the Indicators Provide No Help ............................41 Problems relating to images ...........................................................42 Problems when projection starts.....................................................46 Other problems ...............................................................................46 Using the Help If a problem occurs with the projector, Help uses on-screen displays to assist you in solving the problem. Procedure 37 C Confirm the selection. Using the remote control Using the control panel A Press the [Help] button. The help screen is displayed. Using the remote control Using the control panel Questions and solutions are displayed as shown on the screen below. Press the [Help] button to exit Help. B Select a menu item. q Using the remote control Using the control panel If Help does not provide a solution to the problem, refer to "Problem Solving" (s p.38). Problem Solving If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators" below. If the indicators do not show clearly what the problem might be, refer to "When the Indicators Provide No Help". s p.41 38 Reading the Indicators The projector is provided with the following three indicators that indicate the operating status of the projector. Indicates the operating status. Orange : Standby condition When the [Power] button is pressed in this condition, projection starts. Green (Flashing):Warm-up in progress Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing. Green : Projection in progress Indicates the projection lamp status. Indicates the internal temperature status. Refer to the following table to see what the indicators mean and how to remedy problems that they indicate. If all indicators are off, check that the power cable is connected correctly and that the power is being supplied normally. Sometimes, when the power cable is unplugged, the t indicator remains lit for a short period which is not a fault. Problem Solving 39 f t Power indicator lights red Status Red Red Red Red Problem : Lit Cause Internal Error : Flashing: : Off Remedy or Status Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the International Warranty Terms. sInquiries Fan Error Sensor Error Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the International Warranty Terms. sInquiries Red Red High Temp Error (overheating) Red Red Red Lamp Error Lamp Failure Lamp Cover Open The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector switches to standby mode, so check the following two points. • Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall. • If the air filter is clogged, clean or replace it. s p.50, 56 If the error continues after checking the points above, stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the International Warranty Terms. sInquiries When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On". s p.30 Check the following two points. • Take out the lamp and check if it is cracked. s p.53 • Clean the air filter. s p.50 If it is not cracked - Re-fit the lamp and turn on the power. If the error continues - Replace the lamp with a new lamp and turn on the power. If the error continues - Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the International Warranty Terms. sInquiries If it is cracked - Replace it with a new lamp, or contact your local dealer for further advice. If replacing the lamp yourself, be careful to avoid pieces of broken glass (you cannot continue projecting until the lamp is replaced). sInquiries Check that the lamp cover and the lamp are securely installed. s p.53 If the lamp cover or the lamp is not securely installed, the lamp does not switch on. When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On". s p.30 Problem Solving Warning 40 f i o Indicator is lit or flashing orange Status Red : Lit Cause High Temp Warning : Flashing : Off : Varies according to the projector status Remedy or Status (This is not a problem. However, if the temperature rises too high again, projection stops automatically.) • Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall. • If the air filter is clogged, clean or replace it. s p.50, 56 Orange Replace Lamp Orange Replace it with a new lamp. s p.53 If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode increases. Replace it with a new lamp as soon as possible. q • If the projector is not operating properly, even though the indicators are all showing normal, refer to "When the Indicators Provide No Help" (s p.41). • If an indicator is displaying a status not described in the tables, contact your local dealer or the nearest address provided in the International Warranty Terms. sInquiries Problem Solving 41 When the Indicators Provide No Help If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each problem. Problems when projection starts f Power does not turn on s p.46 Problems relating to images f No images appear s p.42 Projection does not start, the projection area is completely black, the projection area is completely blue, and so on. Other problems f No sound can be heard or the sound is faint s p.46 f The remote control does not work s p.47 f Mail is not received even if a problem occurs with the projector (EMP-83/822 Only) s p.47 f Moving images are not displayed s p.42 Moving images being projected from a computer appear black and nothing is projected. f Projection stops automatically s p.42 f The message "Not supported." is displayed s p.43 f The message "No Signal." is displayed s p.43 f Images are fuzzy or out of focus s p.43 f Interference or distortion appears in images s p.44 Problems such as interference, distortion, or black & white checked patterns appear. f The image is truncated (large) or small, or the aspect is not suitable s p.44 Only part of the image is displayed, or the height and width ratios of the image are not correct, and so on. f Image colors are not right s p.45 The whole image appears purplish or greenish, images are black & white, colors appear dull, and so on. (Computer monitors and LCD screens have different color reproduction performance, so the colors projected by the projector and the colors appearing on the monitor may not necessarily match, but this is not a sign of a problem.) f Images appear dark s p.45 f Nothing appears on the external monitor s p.45 Problem Solving 42 f Problems relating to images f No images appear Check Did you press the [Power] button? Are the indicators switched off? Remedy Press the [Power] button to turn the power on. The power cable is not connected correctly or power is not being supplied normally. Connect the projector's power cable correctly. s Quick Start Guide Check that your electrical outlet or power source is functioning correctly. Press the [A/V Mute] button on the remote control to cancel A/V Mute. s p.15 Open the A/V mute slide. Reset all of the settings. s"Reset"-"Reset All" p.35 Some input images, such as screen savers, may be completely black. Is A/V Mute active? Is the A/V mute slide closed? Are the configuration menu settings correct? Is the projected image completely black? Only when projecting computer images Is the image signal format setting correct? Only when projecting images from a video source Change the setting according to the signal for the connected equipment. s"Signal"-"Video Signal" p.26 f Moving images are not displayed Check Is the computer's image signal being output to the LCD and the monitor? Only when projecting images from a laptop computer or a computer with a built-in LCD screen Remedy Change the image signal to external output only. s Check your computer's documentation. f Projection stops automatically Check Is "Sleep Mode" set to "On"? Remedy Press the [Power] button to turn the power on. If you do not want to use "Sleep Mode", change the setting to "Off". s"Extended"-"Operation"-"Sleep Mode" p.30 Problem Solving f The message "Not supported." is displayed Check Is the image signal format setting correct? Only when projecting images from a video source Do the image signal resolution and the refresh rate correspond to the mode? Only when projecting computer images Refer to the computer's documentation for how to change the image signal resolution and the refresh rate output from the computer. s "List of Supported Monitor Displays" p.70 Remedy Change the setting according to the signal for the connected equipment. s"Signal"-"Video Signal" p.26 43 f The message "No Signal." is displayed Check Are the cables connected correctly? Is the correct input port selected? Is the power for the computer or video source turned on? Are the image signals being output to the projector? Remedy Check that all the cables required for projection are securely connected. s Quick Start Guide Change the image by pressing the [Source Search] button on the remote control or the control panel.s p.13 Turn the power on for the equipment. If the image signals are only being output to the computer's LCD monitor or to the accessory monitor, you need to change the output to an external destination as well as the computer's own monitor. For some Only when projecting images from a laptop computer models, when the image signals are output externally, they no longer appear on the LCD monitor computer or a computer with a built-in LCD screen or accessory monitor. sComputer's documentation, under a title such as "External output" or "Connecting an external monitor". If the connection is made while the power of the projector or computer is already turned on, the function [Fn] key that changes the computer's image signal to external output may not work. Turn the power for the computer and the projector off and then back on again. s Quick Start Guide f Images are fuzzy or out of focus Check Is the focus adjusted correctly? Is the projector at the correct distance? Remedy Turn the focus ring to adjust the focus. s Quick Start Guide For EMP-83/822/X5, the recommended projection distance for Wide ranges from 84 to 867 cm, and for Tele from 101 to 1041 cm. For EMP-S5, the recommended projection distance ranges from 87 to 1050 cm. Setup within this range. s p.59 Lower the projection angle to reduce the amount of keystone correction. s Quick Start Guide If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the projector up in the room about one hour before it is used. If condensation forms on the lens, turn the projector off and wait for the condensation to disappear. Is the Keystone adjustment value too large? Has condensation formed on the lens? Problem Solving f Interference or distortion appear in images Check Is the image signal format setting correct? Only when projecting images from a video source Are the cables connected correctly? Is an extension cable being used? Is the correct resolution selected? Only when projecting computer images Are the "Sync.g" and "Trackingg" settings adjusted correctly? Only when projecting computer images Remedy Change the setting according to the signal for the connected equipment. s"Signal"-"Video Signal" p.26 44 Check that all the cables required for projection are securely connected. s Quick Start Guide If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the projector to check if the cables you are using may be causing the problem. Set the computer so that the signals being output are compatible with the projector. s "List of Supported Monitor Displays" p.70 sComputer documentation Press the [Auto] button on the remote control or the [Enter] button on the control panel to perform automatic adjustment. If the images are not adjusted correctly after using automatic adjustment, you can make the adjustments from "Sync." and "Tracking" in the configuration menu. s"Signal"-"Tracking", "Sync." p.26 f The image is truncated (large) or small, or the aspect is not suitable Check Is a wide panel computer image being projected? Only when projecting computer images Is the image still being enlarged by E-Zoom? Is "Position" adjusted correctly? Remedy Press the [Aspect] button on the remote control to change the aspect mode in the order of "Normal", "4:3", and "16:9". Change the aspect mode according to the resolution. Press the [Esc] button on the remote control to cancel E-Zoom. s p.17 Press the [Auto] button on the remote control or the [Enter] button on the control panel to perform automatic adjustment of the computer image being projected. If the images are not adjusted correctly after using automatic adjustment, you can make the adjustments from "Position" in the configuration menu. Apart from computer image signals, you can adjust other signals while projecting by adjusting "Position" in the configuration menu. s"Signal"-"Position" p.26 If dual display is activated in the "Display Properties" of the computer's control panel, only about half of the image on the computer screen is projected. To display the entire image on the computer screen, turn off the dual display setting. sComputer video driver documentation Set the computer so that the signals being output are compatible with the projector. s "List of Supported Monitor Displays" p.70 sComputer documentation Is the computer set for dual display? Only when projecting computer images Is the correct resolution selected? Only when projecting computer images Problem Solving f Image colors are not right Check Do the input signal settings match the signals from the connected device? Remedy Change the following settings according to the signal for the connected equipment. When projecting images from equipment connected to Computer1, Computer, or Computer2 Input, see s "Signal"-"Computer1/2 Input" p.26 When projecting images from equipment connected to Video or S-Video, see s"Signal"-"Video Signal" p.26 Adjust the "Brightness" setting in the configuration menu. s"Image"-"Brightness" p.24 Check that all the cables required for projection are securely connected. s Quick Start Guide Adjust the "Contrast" setting in the configuration menu. s"Image"-"Contrast" p.24 Adjust the "Color Adjustment" setting in the configuration menu. s"Image"-"Color Adjustment" p.24 Adjust the "Color Saturation" and "Tint" settings in the configuration menu. s"Image"-"Color Saturation", "Tint" p.24 45 Is the image brightness adjusted correctly? Are the cables connected correctly? Is the "Contrastg" setting adjusted correctly? Is the color adjusted correctly? Are the color saturation and tint adjusted correctly? Only when projecting images from a video source f Images appear dark Check Are the image brightness and luminance adjusted correctly? Is the "Contrastg" setting adjusted correctly? Is the lamp due for replacement? Remedy Adjust the "Brightness" and "Brightness Control" settings in the configuration menu. s"Image"-"Brightness" p.24 s"Settings"-"Brightness Control" p.28 Adjust the "Contrast" setting in the configuration menu. s"Image"-"Contrast" p.24 When the lamp is nearly ready for replacement, the images become darker and the color quality becomes poorer. When this happens, replace the lamp with a new lamp. s p.52 f Nothing appears on the external monitor Check Are images from a port other than the Computer1 or Computer Input port being projected? Remedy The only images that can be displayed on an external monitor are computer images from the Computer1 or Computer Input port. s p.61 Problem Solving 46 f Problems when projection starts f Power does not turn on Check Did you press the [Power] button? Are the indicators switched off? Remedy Press the [Power] button to turn the power on. The power cable is not connected correctly or power is not being supplied normally. Connect the projector's power cable correctly. s Quick Start Guide Check that your electrical outlet or power source is functioning correctly. There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power cable. If this does not solve the problem, stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the International Warranty Terms. sInquiries When you press and hold down the [Enter] button on the control panel for about seven seconds, a message is displayed and the lock is released. s p.20 Check the "Remote Receiver" in the configuration menu. s"Settings"-"Remote receiver" p.28 When the operation to the left is performed when "Direct Power On" is set to "On", the power may not turn back on. Press the [Power] button to turn the power back on. Do the indicators turn on and off when the power cable is touched? Is the operation lock set to "Full Lock"? Is the correct setting for the remote receiver selected? (EMP-83/822 only) Was the power cable plugged back in immediately after Direct Power Off, or is the breaker turned off? (EMP-83/822 only) f Other problems f There is no audio or the audio is too low Check Is the audio source connected correctly? Is the volume adjusted to the minimum setting? Is A/V Mute active? Is the audio cable's specification "No resistance"? Remedy Check that the cable is connected to the Audio port. Adjust the volume so that sound can be heard. s Quick Start Guide Press the [A/V Mute] button on the remote control to cancel A/V Mute. s p.15 When using a commercially available audio cable, make sure it is labelled "No resistance". Problem Solving f The remote control does not work Check Remedy Is the remote control light-emitting area pointing towards the Point the remote control towards the remote receiver. remote receiver on the projector when it is operated? The operating angle for the remote control is about 30 horizontally, and about 15 vertically. s Quick Start Guide Is the remote control too far from the projector? The operating range for the remote control is about 6 m. s Quick Start Guide Is direct sunlight or strong light from fluorescent lamps Set the projector up in a location where strong light does not shine onto the remote receiver. For EMP-83/ shining onto the remote receiver? 822, set the remote receiver to "Off" from "Remote Receiver" in the configuration menu. s"Settings""Remote receiver" p.28 Is the correct setting for the remote receiver selected? Check the "Remote Receiver" in the configuration menu. s"Settings"-"Remote receiver" p.28 (EMP-83/822 only) Are the batteries dead or have the batteries been inserted Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary. s p.51 correctly? Was a remote control button pressed for more than If any of the buttons on the remote control are pressed down for more than 30 seconds, the remote control 30 seconds? stops sending signals (remote control's sleep mode). When the button is released, normal remote control operation resumes. This can prevent the batteries from running down accidentally because Sleep Mode operates when the remote control is stored in a bag or if an object is placed on top of it. 47 f Mail is not received even if a problem occurs with the projector (EMP-83/822 Only) Check Is "Standby Mode" set to "Network On"? Remedy To use the Mail Notification function when the projector is in standby, set "Network On" from "Standby Mode" in the configuration menu. s"Extended"-"Standby Mode" p.29 Did a fatal problem occur and the projector come to a sudden When the projector comes to a sudden stop, mail cannot be sent. stop? If the problem continues, contact your local dealer or the nearest address provided in the International Warranty Terms. sInquiries Is power being supplied to the projector? Check that your electrical outlet or power source is functioning correctly. Is the LAN cable connected correctly? Check that the LAN cable is connected correctly. Reconnect it if it is not connected or it is not connected correctly. s p.62 Is "Mail" set correctly in the configuration menu? Mail notification of problems is sent according to the "Mail" settings in the configuration menu. Check if it is set correctly. s"Network Menu"-"Mail Menu" p.32 Appendices This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come. Installation Methods ........................................... 49 Cleaning............................................................... 50 • Cleaning the Projector's Surface .....................................50 • Cleaning the Lens..............................................................50 • Cleaning the Air Filter and Air Intake Vent ..................50 Optional Accessories and Consumables .........64 Optional accessories....................................................................... 64 Consumables .................................................................................. 64 Glossary...............................................................65 ESC/VP21 Commands ........................................67 • Command List .................................................................. 67 • Cable Layouts ................................................................... 67 Serial connection (EMP-83/822 Only) .......................................... 67 Replacing Consumables .................................... 51 • Replacing the Remote Control Batteries ........................51 • Replacing the Lamp ..........................................................52 Lamp replacement period ...............................................................52 How to replace the lamp.................................................................53 Resetting the lamp operating time..................................................55 • Connecting a USB (EMP-X5/S5 Only) ........................... 68 • USB Connection Setup..................................................... 68 • Replacing the Air Filter....................................................56 Air filter replacement period ..........................................................56 How to replace the air filter............................................................56 PJLink (EMP-83/822 Only) ..................................69 Non-compatible commands ........................................................... 69 Input names defined by PJLink and corresponding projector connectors.................................................................................. 69 Manufacturer name displayed for "Manufacture name information query" .................................................................... 69 Model name displayed for "Product name information query" ..... 69 Saving a User's Logo ......................................... 57 Screen Size and Distance .................................. 59 • EMP-83/822/X5 .................................................................59 • EMP-S5 ..............................................................................60 List of Supported Monitor Displays ..................70 Computer image............................................................................. 70 Component Video .......................................................................... 70 Composite video/S-video............................................................... 70 Connecting to External Equipment ................... 61 • Connecting to an External Monitor ................................61 • Connecting to External Speakers (EMP-83/822 Only)..61 Connecting a LAN Cable (EMP-83/822 Only) ... 62 Connecting a USB Cable (EMP-X5/S5 Only) .... 63 Specifications......................................................71 Appearance..........................................................75 Index.....................................................................76 Installation Methods The projector supports the following four different projection methods. 49 Warning • A special method of installation is required when suspending the projector from a ceiling (ceiling mount). If it is not installed correctly, it could fall causing an accident and injury. • If you use adhesives on the ceiling mount to prevent the screws from loosening, or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall from its ceiling mount. This could cause serious injury to anyone under the ceiling mount and could damage the projector. When installing or adjusting the ceiling mount, do not use adhesives to prevent the screws from loosening and do not use oils or lubricants and so on. • Project images from in front of the screen. (Front projection) • Project images from behind a translucent screen. (Rear projection) • Suspend the projector from the ceiling and project images from in front of the screen. (Front/Ceiling projection) • Suspend the projector from the ceiling and project images from behind a translucent screen. (Rear/Ceiling projection) Attention Do not use the projector on its side. This may cause malfunctions to occur. q • An optional ceiling mount is required when suspending the projector from a ceiling. s p.64 • You can change the setting as follows by pressing down the [A/V Mute] button on the remote control for about five seconds. "Front" W "Front/Ceiling" Set "Rear" or "Rear/Ceiling" in the configuration menu. s p.29 Cleaning You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate. 50 Attention If dust collects on the air filter it can cause the internal temperature of the projector to rise, and this can lead to problems with operation and shorten the optical engine's service life. Clean the air filter immediately when the message is displayed. Cleaning the Projector's Surface Clean the projector's surface by wiping it gently with a soft cloth. If the projector is particularly dirty, moisten the cloth with water containing a small amount of neutral detergent, and then firmly wring the cloth dry before using it to wipe the projector's surface. Attention Do not use volatile substances such as wax, alcohol, or thinner to clean the projector's surface. The quality of the case may change or become discolored. Cleaning the Lens Use a commercially available cloth for cleaning glasses to gently wipe the lens. Attention Do not rub the lens with harsh materials or subject the lens to shocks, as it can easily become damaged. q Cleaning the Air Filter and Air Intake Vent Clean the air filter and the air intake vent when the following message is displayed. "The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air filter." s "How to replace the air filter" p.56 • If a message is frequently displayed, even after cleaning, it is time to replace the air filter. Replace it with a new air filter. s p.56 • It is recommended that you clean these parts at least once every three months. Clean them more often than this if using the projector in a particularly dusty environment. Replacing Consumables This section explains how to replace the remote control batteries, the lamp, and the air filter. 51 B Replace the old batteries with new batteries. Caution Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way. Replacing the Remote Control Batteries If delays in the responsiveness of the remote control occur or if it does not operate after it has been used for some time, it probably means that the batteries are becoming flat. When this happens, replace them with new batteries. Have two spare AA-size manganese dry batteries ready to use when required. Attention Make sure you read the Safety Instructions/International Warranty Terms before handling the batteries. sSafety Instructions Procedure C Replace the battery cover. Press the battery cover until it clicks into place. A Remove the battery cover. Catch While pushing the battery cover catch, lift the cover up. Replacing Consumables 52 Replacing the Lamp Attention f Lamp replacement period It is time to replace the lamp when: • The message "Replace the lamp." is displayed. A message is displayed. • The lamp replacement message is set to appear after the following time periods in order to maintain the initial brightness and quality of the projected images. s "Brightness Control" p.28 ·When used continually at high brightness: About 2900 hours ·When used continually at low brightness: About 3900 hours • If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode increases. When the lamp replacement message appears, replace the lamp with a new one as soon as possible, even if it is still working. • Depending on the characteristics of the lamp and the way it has been used, the lamp may become darker or stop working before the lamp warning message appears. You should always have a spare lamp ready in case it is needed. • The lamp indicator flashes orange. Flashing orange • The projected image gets darker or starts to deteriorate. Replacing Consumables 53 f How to replace the lamp Procedure Warning • When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. If replacing the lamp of a projector which has been installed on the ceiling, you should always assume that the lamp is broken, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened. If pieces of glass get into your eyes or mouth, seek medical advice immediately. you turn off the projector's power and the A After confirmation buzzer beeps twice, disconnect the power cable. until the lamp has cooled down, then remove B Wait the lamp cover. Loosen the lamp cover fixing screw with the screwdriver supplied with the new lamp or a + head screwdriver. Then slide the lamp cover straight forward and lift it to remove. Caution • When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. Wait until the lamp has cooled down sufficiently before removing the lamp cover. If the lamp is still hot, burns or other injuries may result. It takes about one hour after the power has been turned off for the lamp to be cool enough. Replacing Consumables 54 C Loosen the two lamp fixing screws. E Install the new lamp. Insert the new lamp along the guide rail in the correct direction so that it fits in place, push down firmly at the location marked "PUSH", and once it is fully inserted tighten the two screws. D Take out the old lamp. If the lamp is cracked, replace it with a new lamp, or contact your local dealer for further advice. sInquiries Replacing Consumables 55 F Replace the lamp cover. Attention • Make sure you install the lamp securely. If the lamp cover is removed, the lamp turns off automatically as a safety precaution. If the lamp or the lamp cover is not installed correctly, the lamp does not turn on. • This product includes a lamp component that contains mercury (Hg). Please consult your local regulations regarding disposal or recycling. Do not dispose of it with normal waste. f Resetting the lamp operating time The projector records how long the lamp is turned on and a message and indicator notify you when it is time to replace the lamp. After replacing the lamp, make sure you reset the lamp hours in the configuration menu. s p.35 q Only reset the lamp operating time after the lamp has been replaced. Otherwise the lamp replacement period is not indicated correctly. Replacing Consumables 56 Replacing the Air Filter f Air filter replacement period It is time to replace the air filter when: • The air filter is ripped. • The message is displayed even though the air filter has been cleaned. C Install the new air filter. Slide the air filter in from the outside and push until it clicks into place. f How to replace the air filter The air filter can be replaced even when the projector is suspended from a ceiling. Procedure you turn off the projector's power and the A After confirmation buzzer beeps twice, disconnect the power cable. q B Remove the air filter. Dispose of used air filters properly in accordance with your local regulations. Do not dispose of it with normal waste. Material quality of the frame section: Polycarbonate, ABS resin Material quality of the filter section: Polyurethane form Put your finger into the recess of the air filter and slide it forward to remove it. Saving a User's Logo You can save the image that is currently being projected as a user's logo. Depending on the area of purchase, the User's Logo function may not be available for EMP-X5/S5. In that case, the user's logo cannot be saved. 57 the configuration menu, select "Extended"B In "User's Logo". s "Using the Configuration Menu" p.23 Check the buttons you can use and the operations they perform in the guide under the menu. q Procedure When a user's logo is saved, the previous user's logo is erased. the image you want to use as the user's A Project logo, and then press the [Menu] button. Using the remote control Using the control panel q • If "User's Logo Protect" from "Password Protect" is set to "On", a message is displayed and the user's logo cannot be changed. You can make changes after setting "User's Logo Protect" to "Off". s p.19 • If "User's Logo" is selected when Keystone, E-Zoom, Aspect, or Progressive are being performed, the function currently being performed is cancelled. "Choose this image as the User's Logo?" is C When displayed, select "Yes". q When you press the [Enter] button on the remote control or the control panel, the screen size may change as it changes to the resolution of the image signal. Saving a User's Logo 58 the box to select the part of the image to use D Move as the user's logo. "Select this image?" is displayed, select E When "Yes". the zoom factor from the zoom setting F Select screen. Using the remote control Using the control panel the message "Save this image as the User's G When Logo?" is displayed, select "Yes". The image is saved. After the image has been saved, the message "Completed" is displayed. q q You can save at up to 400 ^ 300 dots in size. • Saving the user's logo may take about 15 seconds. Do not use the projector or any connected equipment while it is saving. This may cause malfunctions to occur. • Once a user's logo has been saved, the logo cannot be returned to the factory default. Screen Size and Distance EMP-83/822/X5 See the following table to choose the best position for your projector. The values are only a guide. Units: cm (in.) Projection Distance U 4:3 Screen Size Offset V 16:9 Screen Size Minimum Maximum 30" 40" 50" 60" 80" 100" 120" 61 ^ 46 (24 ^ 18) 81 ^ 61 (32 ^ 24) 100 ^ 76 (39 ^ 30) 120 ^ 90 (47 ^ 35) 160 ^ 120 (63 ^ 47) 200 ^ 150 (79 ^ 59) 240 ^ 180 (94 ^ 71) (Wide) to (Tele) 84 to 101 (33 to 40) 5 (1.9) 6 (2.5) 8 (3.1) 10 (3.8) 13 (5.0) 16 (6.3) 19 (7.5) 24 (9.4) 32 (12.5) 48 (18.8) 30" 40" 50" 60" 80" 66 ^ 37 (26 ^ 15) 89 ^ 50 (35 ^ 20) 110 ^ 62 (43 ^ 24) 130 ^ 75 (51 ^ 28) 180 ^ 100 (71 ^ 39) 59 Units: cm (in.) Projection Distance U Minimum Maximum (Wide) to (Tele) 91 to 110 (36 to 43) 123 to 148 (48 to 58) 154 to 186 (61 to 73) 186 to 224 (73 to 88) 249 to 300 (98 to 118) 312 to 376 (123 to 148) 375 to 452 (148 to 178) 470 to 565 (185 to 223) 628 to 755 (247 to 297) 944 (372) Offset V (When image position is off center) -1 (-0.4) -1 (-0.5) -2 (-0.7) -2 (-0.8) -3 (-1.1) -3 (-1.4) -4 (-1.6) -5 (-2.0) -7 (-2.7) -10 (-4.1) 113 to 136 (44 to 53) 142 to 171 (56 to 67) 171 to 206 (67 to 81) 229 to 275 (90 to 108) 287 to 345 (113 to 136) 345 to 415 (136 to 163) 432 to 519 (170 to 204) 577 to 693 (227 to 273) 867 to 1041 (341 to 410) 100" 220 ^ 120 (87 ^ 47) 120" 270 ^ 150 (106 ^ 59) 150" 330 ^ 190 (130 ^ 75) 200" 440 ^ 250 (173 ^ 98) 300" 660 ^ 370 (260 ^ 146) 150" 300 ^ 230 (118 ^ 91) 200" 410 ^ 300 (161 ^ 118) 300" 610 ^ 460 (240 ^ 181) Screen 90° Center of lens Screen 90° Center of lens Screen Size and Distance 60 EMP-S5 See the following table to choose the best position for your projector. The values are only a guide. Units: cm (in.) Projection Distance U Offset V 4:3 Screen Size 16:9 Screen Size 30" 40" 50" 60" 80" 100" 120" 61 ^ 46 (24 ^ 18) 81 ^ 61 (32 ^ 24) 100 ^ 76 (39 ^ 30) 120 ^ 90 (47 ^ 35) 160 ^ 120 (63 ^ 47) 200 ^ 150 (79 ^ 59) 240 ^ 180 (94 ^ 71) Minimum Maximum (Wide) to (Tele) 87 to 119 (34 to 47) 117 to 159 (46 to 63) 147 to 200 (58 to 79) 177 to 240 (70 to 95) 237 to 321 (93 to 126) 297 to 402 (117 to 158) 357 to 483 (141 to 190) 447 to 605 (176 to 238) 597 to 807 (235 to 318) 897 (353) Wide to Tele 4 to -2 (1.7 to -0.9) 6 to -3 (2.3 to -1.1) 7 to -4 (2.8 to -1.4) 9 to -4 (3.4 to -1.7) 11 to -6 (4.5 to -2.3) 14 to -7 (5.7 to -2.9) 17 to -9 (6.8 to -3.4) 22 to -11 (8.5 to -4.3) 29 to -15 (11.3 to -5.7) 43 (17.0) 30" 40" 50" 60" 80" 66 ^ 37 (26 ^ 15) 89 ^ 50 (35 ^ 20) 110 ^ 62 (43 ^ 24) 130 ^ 75 (51 ^ 28) 180 ^ 100 (71 ^ 39) Projection Distance U Minimum Maximum (Wide) to (Tele) 95 to 129 (37 to 51) 128 to 173 (50 to 68) 160 to 218 (63 to 86) 193 to 262 (76 to 103) 258 to 350 (102 to 138) 324 to 438 (127 to 172) 389 to 526 (153 to 207) 487 to 659 (192 to 259) 651 to 879 (256 to 346) Units: cm (in.) Offset V (When image position is off center) Wide to Tele -2 to -9 (-0.6 to -3.4) -2 to -11 (-0.8 to -4.5) -3 to -14 (-1.0 to -5.6) -3 to -17 (-1.2 to -6.8) -4 to -23 (-1.6 to -9.0) -5 to -29 (-2.0 to -11.3) -6 to -34 (-2.4 to -13.5) -8 to -43 (-3.0 to -16.9) -10 to -57 (-4.0 to -22.6) 100" 220 ^ 120 (87 ^ 47) 120" 270 ^ 150 (106 ^ 59) 150" 330 ^ 190 (130 ^ 75) 200" 440 ^ 250 (173 ^ 98) 150" 300 ^ 230 (118 ^ 91) 200" 410 ^ 300 (161 ^ 118) 300" 610 ^ 460 (240 ^ 181) Screen 90° Center of lens Screen 90° Center of lens Connecting to External Equipment Connecting to an External Monitor Computer images being input to the Computer1 input port or the Computer Input port can be displayed on an external monitor and the screen at the same time when connected to the projector. This means that you can check projected images on an external monitor when giving presentations even if you cannot see the screen. Connect to an external monitor using the cable supplied with the monitor. 61 Connecting to External Speakers (EMP-83/822 Only) You can connect speakers with built-in amplifiers to the projector's Audio Out port to enjoy a fuller quality of sound. Connect with a commercially available audio cable (pin plug W 3.5 mm stereo mini plug and so on). Use an audio cable compatible with the connector on the external speakers. To external speakers Cable supplied with monitor Monitor port To Monitor Out port Audio cable (commercially available) To Audio Out port q • Component video signals and images connected to the Computer2 port, Video port, and S-Video port cannot be output to an external monitor. • The setting gauge for Keystone, the configuration and help screen, and so on are not output to an external monitor. q When an audio cable plug is inserted in the Audio Out port, the audio changes to the external destination, and audio is no longer emitted from the projector's built-in speaker. Connecting a LAN Cable (EMP-83/822 Only) Connect with a commercially available 100baseTX or 10baseT type LAN cable. 62 To LAN port LAN cable (commercially available) To LAN port Attention To prevent malfunctions, use a category 5 shielded LAN cable. Connecting a USB Cable (EMP-X5/S5 Only) Connect the USBg port of a computer and the USBport (TypeB) on the rear of the projector with a commercially available USB cable. 63 To USB port USB cable To USB port (Type B) Optional Accessories and Consumables Prepare the following options and consumables. Purchase depending on usage. The following list of optional accessories is current as of March, 2007. Details of accessories are subject to change without notice and availability may vary depending on the country of purchase. 64 f Consumables Lamp unit (For EMP-X5/S5) ELPLP41 Lamp unit (For EMP-83/822) ELPLP42 Use as a replacement for used lamps. Air filter (by 2) ELPAF13 Use as a replacement for used air filters. f Optional accessories Soft carrying case ELPKS16B Use this case if you need to travel with the projector. 60" portable screen ELPSC07 80" portable screen ELPSC08 100" screen ELPSC10 Portable roll-type screens (Aspect ratiog 4:3) 50" portable screen ELPSC06 A compact screen that can be carried easily. (Aspect ratio 4:3) HD-15 cable ELPKC02 (1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin) This is the same as the computer cable supplied with the projector. HD-15 cable ELPKC09 (3 m - for mini D-Sub15-pin/mini D-Sub 15pin) HD-15 PC cable ELPKC10 (20 m - for mini D-Sub15-pin/mini D-Sub 15pin) Use one of these longer cables if the computer cable bundled with the product is too short. Component video cable ELPKC19 (3 m - for mini D-Sub 15-pin/RCA male^3) Use to connect a component videog source Ceiling plate* ELPFC03 Pipe 370 (370 mm silver)* ELPFP04 Pipe 570 (570 mm silver)* ELPFP05 Pipe 770 (770 mm silver)* ELPFP06 Ceiling mount (For use with the ceiling plate)* ELPMB18 Use when installing the projector on a ceiling. * A special method of installation is required to suspend the projector from a ceiling. Contact your dealer or the nearest address provided in the International Warranty Terms if you want to use this installation method. sInquiries Glossary This section briefly explains terms that are used with the projector and difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications. Aspect ratio Component Video Composite video 65 Contrast DHCP Dolby Digital Gateway address HDTV Interlace IP address Progressive Refresh rate SDTV SNMP SNMP Trap IP address The ratio between an image's length and its height. HDTV images have an aspect ratio of 16:9 and appear elongated. The aspect ratio for standard images is 4:3. A video signal which has the luminance component and color component separated to provide better image quality. Refers to images that consist of three independent signals: Y (luminance signal), Pb and Pr (color difference signals). Video signals that have the video brightness signals and color signals mixed together. The type of signals commonly used by household video equipment (NTSC, PAL, and SECAM formats). The carrier signal Y (luminance signal) and chroma (color) signal that are contained in the color bar are overlapped to form a single signal. The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or to make them appear softer. Adjusting this particular property of an image is called "contrast adjustment". An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP addressg to equipment connected to a network. A sound format developed by Dolby Laboratories. Normal stereo is a 2-channel format that uses two speakers. Dolby Digital is a 6channel (5.1-channel) system which adds to this a center speaker, two rear speakers, and a sub-woofer. This is a server (router) for communicating across a network (subnet) divided according to subnet masksg. An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions. • Vertical resolution of 720p or 1080i or greater (p = progressiveg, i = interlaceg) • Screen aspect ratiog of 16:9 • Dolby Digitalg audio reception and playback (or output) A method of image scanning whereby the image data is divided into fine horizontal lines that are displayed in sequence starting from left to right and then from top to bottom. The even-numbered lines and odd-numbered lines are displayed alternately. A number to identify a computer connected to a network. A method of image scanning whereby the image data from a single image is scanned sequentially from top to bottom to create a single image. The light-emitting element of a display maintains the same luminosity and color for an extremely short time. Because of this, the image must be scanned many times per second to refresh the light-emitting element. The number of refresh operations per second is called the Refresh rate and is expressed in hertz (Hz). An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTVg High-Definition Television. An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and computers connected to a TCP/IP network. This is the IP addressg for the destination computer used for error notification in SNMP Glossary 66 Squeeze mode sRGB Subnet mask SVGA S-Video SXGA Synchronization Tracking VGA XGA In this mode, wide-screen images in 16:9 mode are compressed in the horizontal direction so that they are stored on the recording medium as 4:3 images.
Лучшая цена на лампу для проектора EPSON EMP -750. Большой выбор между оригинальными и неоригинальными лампами, а так же лампами с.
- 2. Notations Used in This Guide f Safety Indications. So that you can use the projector safely and correctly, symbols are applied in the documentation and on the.
- EPSON EMP - X5 Проекторы инструкция по эксплуатации, характеристики и руководство пользователя загрузить бесплатно в формате pdf на русском.
- L271, Epson ELPLP41 – лампа для проектора Epson EMP - X5, EB-S6, EB-S62, Вместе с лампой вы получите подробную инструкцию по ее замене.
Выберете модель телевизора EPSON, для которого ищете сменную лампу Если Вы не нашли производителя Вашего телевизора EPSON в нашем каталоге. Кликнув на заглавие, откроете более подробную информацию: Её может провести каждый, используя инструкцию к проектору, либо по.
User's Guide
![](https://stat002.fosite.ru/counters/4286496.gif?ui=4286496&ci=91&dn=abc-cloud67.fosite.ru&un=abc-cloud67.fosite.ru&lg=ru&visitorid=-1&stid=1&stdb=1&color1=424242&color2=CECBBD&color3=A8AAC0&color4=7b7b7b&color5=CAC299&turn_on=on&img=0&"+mlp_r+"&)